I don't know why this thing fails in desktop Safari. I'm using Modernizr (which is bundled with the highly recommendedHTML5 Boilerplate) which reports that the Geolocation API is supported but I'm unable to even get any dialog asking the user for permission to geolocate (which is, if I read the draft correctly, REQUIRED to be implemented).
Also, it seems that others (quite a few people actually) have had this same problem but I have been unable to find a solution yet. Below is a snippet from the code; in desktop Safari the PositionErrorCallback (the latter cb function) gets called after timeout but no luck with PositionCallback, no matter how long the timeout value is. Other tested browsers work as expected.
Referenced in other places:
If this is bound to the window resize event, then the
jQuery resize event plugin by "Cowboy" Ben Alman
should be used as it throttles the window resize events.
See: http://benalman.com/projects/jquery-resize-plugin/"
The plugin uses HTML Canvas to render the Boids, so a modern browser with Canvas support is required for this to work. I tested with Chrome, Safari and Firefox. IE with Excanvas was painfully slow…
Update 2: The sensor is now outside, and running on parasitic power.
Update: The data is now available in a more mobile-friendly web page here.
Arduino code, based on (i.e. copypasted & modified a little) stuff from http://www.dial911anddie.com/weblog/2009/12/arduino-ethershield-1wire-temperature-sensor-pachube/ is below. Requires the 1-wire library and the Dallas Temperature Control library, both of which can be downloaded from here. Original code utilized DHCP, but I found this to be somewhat unstable and went with a static IP address instead.
DS18B20 gets it's power from Arduino, and the data line (that's the center pin) is connected to Arduino pin 8. Data line is pulled up to +5V through a 4k7 resistor, as suggested in Maxim literature. Parasitic power supply was not used as proper voltage was readily available from Arduino. Please note that even though parasitic power is not used, the pull-up resistor is still necessary (see the data sheet).
#include <Ethernet.h>
#include <OneWire.h>
#include <DallasTemperature.h>
char PACHUBE_API_STRING[] = ""; // Your API key
int PACHUBE_FEED_ID = 0; // Your feed ID
// Digital IO port used for one wire interface
int ONE_WIRE_BUS = 8 ;
// Ethernet mac address - this needs to be unique
byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
// IP addres of www.pachube.com
byte server[] = { 209,40,205,190 };
// Arduino address
byte ip[] = { 10, 0, 0, 223 };
byte gateway[] = { 10, 0, 0, 2 };
char version[] = "PachubeClient Ver 0.01c";
#define CRLF "rn"
// simple web client to connect to Pachube.com
Client client(server, 80);
// Setup a oneWire instance to communicate with any OneWire device
OneWire oneWire(ONE_WIRE_BUS);
// Pass our oneWire reference to Dallas Temperature.
DallasTemperature sensors(&oneWire);
// 1wire device address
DeviceAddress thermometer;
void setup()
{
// Note: Ethernet shield uses digitial IO pins 10,11,12, and 13
Serial.begin(9600);
Serial.println(version);
Serial.println();
// locate devices on the 1Wire bus
Serial.print("Locating devices on 1Wire bus...");
sensors.begin();
int count = sensors.getDeviceCount();
Serial.print("Found ");
Serial.print( count );
Serial.println(" devices on 1wire bus");
// select the first sensor
for ( int i=0; i<count; i++ )
{
if ( sensors.getAddress(thermometer, i) )
{
Serial.print("1wire device ");
Serial.print(i);
Serial.print(" has address: ");
printAddress(thermometer);
Serial.println();
}
else
{
Serial.print("Unable to find address for 1wire device ");
Serial.println( i );
}
}
// show the addresses we found on the bus
Serial.print("Using 1wire device: ");
printAddress(thermometer);
Serial.println();
// set the resolution to 9 bit
sensors.setResolution(thermometer, 9);
Serial.print("Initializing ethernet...");
delay(5000);
Ethernet.begin(mac, ip, gateway);
delay(5000);
Serial.println(" done.");
}
void sendData()
{
float temp = sensors.getTempC(thermometer);
//float temp = sensors.getTempF(thermometer);
Serial.print("Temp=");
Serial.println(temp);
Serial.println("connecting...");
if (client.connect())
{
Serial.println("connected");
client.print(
"PUT /api/feeds/" );
client.print(PACHUBE_FEED_ID);
client.print(".csv HTTP/1.1" CRLF
"User-Agent: Fluffy Arduino Ver 0.01" CRLF
"Host: www.pachube.com" CRLF
"Accept: */" "*" CRLF // need to fix this
"X-PachubeApiKey: " );
client.print(PACHUBE_API_STRING);
client.print( CRLF
"Content-Length: 5" CRLF
"Content-Type: application/x-www-form-urlencoded" CRLF
CRLF );
client.println(temp);
unsigned long reqTime = millis();
// wait for a response and disconnect
while ( millis() < reqTime + 10000) // wait 10 seconds for response
{
if (client.available())
{
char c = client.read();
Serial.print(c);
}
if (!client.connected())
{
Serial.println();
Serial.println("server disconnected");
break;
}
}
Serial.println("client disconnecting");
Serial.println("");
client.stop();
}
else
{
Serial.println("connection failed");
}
}
void printAddress(DeviceAddress deviceAddress)
{
for (uint8_t i = 0; i < 8; i++)
{
if (deviceAddress[i] < 16) Serial.print("0");
Serial.print(deviceAddress[i], HEX);
}
}
void loop()
{
sensors.requestTemperatures(); // Send the command to get temperatures
sendData();
delay( ( 5l * 60l * 1000l) - 11000l ); // wait 5 minutes
}
